SCT 60-22 dust collection adapter and shop vac hose guide
Measure to order
Dust port
Look at the dust port on your Hilti SCT 60-22. If it sticks out like a tube, measure the outside. On the SCT 60-22, if it is a hole, measure the inside. Use calipers.
More on this port size →Get the adapter for this tool. Printed to order from $12.99, plus $7.95 shipping.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Hilti Nuron SCT 60-22 Cordless Table Saw
Specifications
Connect your Hilti SCT 60-22 to your shop vac
Measure the SCT 60-22 port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Hilti SCT 60-22 is a cordless table saw on the Nuron battery platform. It is built for job sites, where you often cut inside finished rooms. That makes a clean dust hookup worth even more than it is in a home shop.
The saw has a dust port at the rear. We print our adapter to the size you measure there. A GulpDust PETG adapter matches the port on one end and your shop vac hose on the other.
Hilti SCT 60-22 Specs
| Port location | Rear |
|---|---|
| Connection type | Press on |
| Power | Cordless, Nuron platform |
Hilti SCT 60-22 Dust Port: What Connects To It
The SCT 60-22 has a dust port at the back of the saw. We print the adapter to the size you measure there.
It is the size class dust extractor hoses use. A standard shop vac hose is far too big to seal on it.
That gap is where a GulpDust adapter earns its keep. It grips the saw port on one end and your vac hose on the other, so the connection holds and the suction stays at the blade.
How to Connect a Shop Vac to the Hilti SCT 60-22
Take the battery out first. Then wipe the sawdust off the rear port so the adapter seats clean.
Press the tool end of the PETG adapter into the port. We print it to the size you measure, so a firm push is all it takes. Then press your shop vac or extractor hose onto the other end.
Turn the vac on before the blade touches wood. A table saw fires chips down through the blade slot from the first inch of the cut.
Why a Cordless Table Saw Still Needs a Dust Hookup
Cutting the cord does not cut the dust. The SCT 60-22 makes the same chips and fine dust a corded saw makes.
On a job site you often cut in rooms that are already finished. A sealed dust hookup keeps the room clean and keeps fine dust out of the air you breathe.
Any shop vac or extractor with the right adapter does the main job. The fit at the port is what matters most.
Hilti SCT 60-22 Dust Collection FAQ
What size is the dust port on the Hilti SCT 60-22?+
Measure it with calipers. It is at the rear. We print the adapter to the size you measure there. One end grips the saw, the other end matches your hose.
Will a regular shop vac hose fit the SCT 60-22 port?+
Not by itself. Most shop vac hoses are 1-7/8 inch or 2-1/2 inch, so measure the port on your tool and the hose end on your vac. The GulpDust PETG adapter bridges the gap.
Will a dust extractor hose fit the port?+
It may. Extractor hoses run in the same small size class this saw uses. Hose ends still vary by brand, so our adapter is the surer path.
Do I need clamps to attach the adapter?+
Usually not. We print the adapter to the size you measure, so you press it in and it holds. The vac hose end works the same way. Add a wrap of tape at any joint that sees heavy use.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
