35mm Dust Port Tools and Vacuum Adapter Guide for Bosch PROFACTOR and WEN Saws
A 35mm dust port is the size Bosch built into its Click and Clean dust system. The port is round, 35mm across on the inside and about 40mm on the outside. Click and Clean is a quick-twist lock that grabs the hose, so it does not need a screw or a clamp to hold.
The 35mm group is Bosch PROFACTOR plus WEN's saws. Some other tools get labeled 35mm and measure smaller at the tool port, closer to 28 to 32mm. Each tool detail page carries its own number.
Below is every tool with a 35mm dust port that we track. Each link goes to that tool's full page with the exact size and the adapter that fits.
Power Tools With a 35mm Dust Port
Every tool we list with a 35mm port. Linked tools open their full specs and the exact adapter that fits.
Bosch2 tools
WEN4 tools
The Adapter That Fits a 35mm Port
Each adapter grips the 35mm inside of the tool port on one end and steps it to your shop vac or dust extractor hose on the other end. Friction fit, no clamps. Made in the USA.
What 35mm Means on a Tool Port
The 35mm port is round. It measures 35mm on the inside and 40mm on the outside. On Bosch PROFACTOR tools, a Click and Clean hose end snaps onto the port with a quarter turn.
If you do not own a Bosch vac, your shop vac hose is almost certainly the wrong size. A 1-7/8 in. or 2-1/2 in. hose end is much larger than 35mm. A sized PETG adapter bridges the gap so the tool pulls dust into your vac instead of past it.
How to Connect a Shop Vac to a 35mm Bosch PROFACTOR Tool
First, look at the rear of the saw. The 35mm dust port sits at the back of the housing. Clear any dust out of it for a clean fit.
Press the tool end of the PETG adapter into the 35mm port. It holds with a firm push. Then press your shop vac hose onto the other end of the adapter. Turn the vac on before you start the cut.
Why Bosch Sanders Are Not on This Hub
Three Bosch sanders often get listed at 35mm: the GET75-6N, the ROS20VSK, and the GEX18V-2CN. Their tool ports are closer to 28mm. The 35mm number on those listings is the shop vac hose size, not the tool port.
Each of those sanders has its own tool detail page with its port size. Use the tool page, not this hub, to pick the right adapter.
35mm Dust Port FAQ
Which power tools use a 35mm dust port?
Six tools sit in the 35mm family: the Bosch GKS18V-25GCN and GKT18V-20GCN PROFACTOR saws, the WEN CT1065 and 20691 track saws (exactly 35.0mm), and the WEN CT1525 and 20625 circular saws (35.56 and 34.8mm, inside the same friction-fit band). Other tools get labeled 35mm and measure smaller. Open the detail page for the tool you own.
What is Click and Clean?
Click and Clean is the name Bosch uses for its dust port and hose system. The 35mm port is part of it. The hose end twists onto the port with a quarter turn and locks in place without a clamp.
Can I use a regular shop vac with a 35mm Bosch PROFACTOR tool?
Yes, with an adapter. Most US shop vac hoses are 1-7/8 in. or 2-1/2 in., both wider than 35mm. The GulpDust PETG adapter is sized to the 35mm port on one end and to your vac hose on the other.
Do I need clamps or tape for the adapter?
No. The adapter is a friction fit. You push the tool end into the 35mm port and it holds. The shop vac hose end works the same way.
Do you sell the design file?
No. We sell the finished part. Each 35mm adapter is printed to order in PETG and ships from the US.