C3610DRJQ4 dust collection adapter and shop vac hose guide
Measure to order
Dust port
Look at the dust port on your Metabo HPT C3610DRJQ4. If it sticks out like a tube, measure the outside. On the C3610DRJQ4, if it is a hole, measure the inside. Use calipers.
More on this port size →Get the adapter for this tool. Printed to order from $14.99, plus $7.95 shipping.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Metabo HPT 36V MultiVolt 10 in. Table Saw
Specifications
Connect your Metabo HPT C3610DRJQ4 to your shop vac
Measure the C3610DRJQ4 port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Metabo HPT C3610DRJQ4 is a 36V MultiVolt 10 in. table saw. It cuts without a cord, but it makes the same pile of chips every table saw makes. Most of those chips go down through the blade slot and out the rear port.
The saw has a dust port at the rear. We print our adapter to the size you measure there. A GulpDust PETG adapter matches the port on one end and your shop vac hose on the other.
Metabo HPT C3610DRJQ4 Specs
| Port location | Rear |
|---|---|
| Connection type | Press on |
| Blade size | 10 in. |
| Power | 36V MultiVolt |
Metabo HPT C3610DRJQ4 Dust Port: What Connects To It
The C3610DRJQ4 has a dust port at the back of the saw. We print the adapter to the size you measure there.
Hose cuffs vary a lot by brand. A hose that grabs one saw can wiggle loose on another. Loose means it leaks right where the saw makes the most dust.
A GulpDust adapter is sized to grip your port on one end and your vac hose on the other, so the connection holds and the suction stays at the blade.
How to Connect a Shop Vac to the Metabo HPT C3610DRJQ4
Power the saw down and take the battery out first. Then wipe the sawdust off the rear port so the adapter seats clean.
Press the PETG adapter onto the port. We print it to the size you measure, so a firm push is all it takes. Then press your shop vac hose onto the other end.
Turn the vac on before the blade touches wood. A table saw fires chips down through the blade slot the moment the cut starts, so the vac needs to be pulling from the first inch.
Why Table Saws Need Dust Collection
A table saw throws more chips than any other tool in the shop. Rip a few boards with an open port and the floor behind the saw turns white.
The chips you see are only part of it. The blade also makes fine dust that hangs in the air and gets into your lungs.
Sealing the rear port sends both into the vac. It is the single biggest dust win you can get on this saw.
Metabo HPT C3610DRJQ4 Dust Collection FAQ
What size is the dust port on the Metabo HPT C3610DRJQ4?+
Measure it with calipers. It is at the rear of the saw. We print the adapter to the size you measure there. You pick the hose end you need.
Does the C3610DRJQ4 work with a regular shop vac?+
Yes. Hose cuffs still vary by brand, so if your hose sits loose on the port, a printed adapter holds the joint tight.
Where does the dust go on this saw?+
Most of it drops through the blade slot and out the rear port. That port is the one worth hooking up.
Do I need clamps to attach the adapter?+
Usually not. We print the adapter to the size you measure, so it presses in and holds. You press it on and it holds. The vac hose end works the same way. Add a wrap of tape at any joint that sees heavy use.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
