TSS102L dust collection adapter and shop vac hose guide
Measure to order
Dust port
Look at the dust port on your Ryobi TSS102L. If it sticks out like a tube, measure the outside. On the TSS102L, if it is a hole, measure the inside. Use calipers.
Get the adapter for this tool. Printed to order from $12.99, plus $7.95 shipping.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Ryobi 10 in. Sliding Compound Miter Saw
Specifications
Connect your Ryobi TSS102L to your shop vac
Measure the TSS102L port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Ryobi TSS102L is a 10 inch sliding compound miter saw. A miter saw throws a big pile of chips on every cut. A vac at the port catches most of them before they land on your work and your floor.
The saw has a dust port at the rear. We print a GulpDust PETG adapter to your port measurement on one end and to your shop vac hose on the other end.
Ryobi TSS102L Specs
| Port location | Rear |
|---|---|
| Connection type | Press on |
| Blade size | 10 in. |
| Tool type | Sliding compound miter saw |
Ryobi TSS102L Dust Port: What Connects To It
The dust port on the TSS102L sits at the rear. We print the PETG adapter to the size you measure there.
Most shop vac hoses are 1-7/8 in. or 2-1/2 in. Neither one seals on this port on its own, so dust blows out the joint on every cut.
The adapter matches the saw port on one end and your vac hose on the other end for a tight fit.
Keeping the Adapter Seated on a Sliding Head
The head on this saw slides forward and back, and the hose gets dragged along with it.
The adapter grips the port all the way around, so the tug does not pull it loose.
Leave a little slack in the hose. Let it hang, and the slide travels freely through the whole cut.
Why Dust Collection Matters on a Sliding Miter Saw
A sliding miter saw makes a big pile of chips fast. Those chips spray back behind the fence and pile up on the bench and the floor.
Pulling the chips at the port keeps your work area clear and keeps more of the fine dust out of the air you breathe. It also helps you see your cut line so your cuts stay clean.
Run a steady vac the whole time you cut. Any shop vac with the right adapter does the main job.
Ryobi TSS102L Dust Collection FAQ
What fits the dust port on the Ryobi TSS102L?+
Our PETG adapter does. One end presses into the saw port. The other end takes your shop vac hose.
Does the Ryobi TSS102L work with a regular shop vac?+
Yes, with an adapter. Most shop vac hoses are 1-7/8 in. or 2-1/2 in., which do not seal on this port on their own. We print the GulpDust PETG adapter to your saw port measurement on one end and to your vac hose size on the other.
Is the dust bag enough on its own?+
No. The bag catches the big chips and lets the fine dust through. A vac at the port pulls far more of it.
Do I need clamps to attach the adapter?+
Usually not. We print the adapter to the size you measure, so you press it into the port and it holds. The vac hose end works the same way. Add a wrap of tape at any joint that sees heavy use.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
