50110CC-WHD dust collection adapter and shop vac hose guide
Measure to order
Dust port
Round port, friction
Look at the dust port on your Wahuda 50110CC-WHD. If it sticks out like a tube, measure the outside. On the 50110CC-WHD, if it is a hole, measure the inside. Use calipers.
More on this port size →Get the adapter for this tool. Printed to order from $20.99, plus $7.95 shipping.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Wahuda 10 in. Benchtop Jointer
Specifications
Connect your Wahuda 50110CC-WHD to your shop vac
Measure the 50110CC-WHD port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Wahuda 50110CC-WHD is a 10 inch benchtop jointer. A jointer flattens the face and squares the edge of rough boards, and it throws a steady stream of chips while it works. A good dust hookup pulls those chips away before they pile up.
The jointer has a dust port at the rear, plus a step-down adapter in the box for 2-1/2 in. hose. A GulpDust PETG adapter mates the port or the included step-down to your hose to the size you measure.
Wahuda 50110CC-WHD Specs
| Port shape | Round |
|---|---|
| Included step-down adapter | 2-1/2 in. hose |
| Port location | Rear |
| Connection type | Press on |
| Jointer width | 10 in. |
Wahuda 50110CC Dust Port: What Connects To It
Wahuda builds this jointer with a rear dust port made for dust collector hose. A step-down adapter for 2-1/2 in. hose comes in the box.
Our PETG adapter fits either end of that chain, the main port or the included step-down.
If your hose does not match what came in the box, the adapter bridges the gap. One end is printed to your jointer measurement, the other end to your hose size.
Shop Vac or Dust Collector: Two Ways to Hook Up the Wahuda
Got a dust collector? Run its hose to the main port. That gives the most airflow, and a jointer makes enough chips to use it.
Got a shop vac? Fit the included step-down, then match your vac hose to it. Many shop vac hose ends still need one more adapter to fit tight.
Either way, press the PETG adapter on with a firm push. It holds.
Why a Benchtop Jointer Needs Dust Collection
A jointer peels off long shavings and fine dust with every pass. Those shavings pile up fast and can clog the chute if nothing pulls them out.
A clogged chute can push chips back under the board as it feeds and dent the fresh surface. Steady suction keeps the cut clean.
Clean boards also mean clean glue lines. Pulling the dust at the port is an easy step that shows up in the final fit.
Wahuda 50110CC-WHD Dust Collection FAQ
What fits the dust port on the Wahuda 50110CC jointer?+
Our PETG adapter does. It mates the jointer port, or the step-down that came in the box, to your hose.
Does the Wahuda 50110CC work with a regular shop vac?+
Yes. Fit the included step-down adapter, then match your vac hose to it. If the ends do not match, a GulpDust adapter bridges the gap.
Can I hook the Wahuda jointer to a dust collector?+
Yes. Measure the main port and your collector fitting. If your collector fitting is a different size, our adapter bridges it.
Can I use one adapter on the 6, 8, and 10 inch Wahuda jointers?+
Maybe. Port sizes can change between models. Measure the port on your tool and give us that number.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
