Craftsman CMXEMAX69434501 Miter Saw Dust Port Size and Shop Vac Adapter Guide
Craftsman 10 in. Sliding Compound Miter Saw
Specifications
Connect your Craftsman CMXEMAX69434501 to your shop vac
Pick what you are connecting to. Each one is a finished PETG adapter, sized for both ends. Print it yourself or have it shipped, made in the USA.
Standard hose & duct sizes
Popular vacuums & extractors
Not sure which size? Walk through the configurator or measure your port.
Craftsman CMXEMAX69434501 Miter Saw Dust Port Size and Shop Vac Adapter Guide
The Craftsman CMXEMAX69434501 is a 10 inch sliding compound miter saw. A miter saw throws a big pile of chips on every cut. A vac at the port catches most of them before they land on your work and your floor.
The saw has a round dust port at the rear. One community adapter listing sizes it to about 38.1 mm, which is 1-1/2 inch. That is a single measurement, not a hard spec, so measure your own port with calipers before you buy. A GulpDust PETG adapter is sized to the port on one end and your shop vac hose on the other end. No tape. No clamps.
Craftsman CMXEMAX69434501 Dust Port and Specs
Port size: please measure to confirm
Source verified, but only one side of the port was confirmed. Measure your port before you buy.
Source we cite: makerworld.com
| Dust port inner diameter | 38.1mm (1-1/2 in.) (measure to confirm) |
| Port shape | Round |
| Port location | Rear |
| Connection type | Friction fit |
| Blade size | 10 in. |
Craftsman CMXEMAX69434501 Dust Port Size: Round, About 38.1 mm Inside
The dust port on the CMXEMAX69434501 is round. One community adapter listing puts the inside at about 38.1 mm, which is a common 1-1/2 inch size.
Treat that number as a close guide, not a hard spec. It is a single community measurement, not a caliper reading on our bench. Measure your own port before you order so you get the right size.
Most shop vac hoses are 1-7/8 inch or 2-1/2 inch. Those do not seal on a 38.1 mm port on their own. A GulpDust adapter matches the saw port on one end and your vac hose on the other end for a tight fit.
How to Measure Your Craftsman CMXEMAX69434501 Dust Port
Slide the inside jaws of your calipers into the port and open them out until they touch the inner wall. That gives you the inner diameter. You should read close to 38.1 mm, or about 1-1/2 inch.
Then close the caliper jaws around the outside of the port stub for the outer diameter. The inner is what the adapter plugs into, so that reading matters most.
Write down what you measure and order the adapter to match. A quick check makes sure you order a size that seals tight.
Why Dust Collection Matters on a Sliding Miter Saw
A sliding miter saw makes a big pile of chips fast. Those chips spray back behind the fence and pile up on the bench and the floor.
Pulling the chips at the port keeps your work area clear and keeps the fine dust out of the air you breathe. It also helps you see your cut line so your cuts stay clean.
For the best result, match the adapter to the port and run a steady vac while you cut. Any shop vac with the right adapter does the main job.
Craftsman CMXEMAX69434501 Dust Collection FAQ
What size is the dust port on the Craftsman CMXEMAX69434501?+
One community adapter listing sizes it to about 38.1 mm, which is 1-1/2 inch. That is a single measurement, not a hard spec, so measure your own port with calipers before you buy.
Does the Craftsman CMXEMAX69434501 work with a regular shop vac?+
Yes, with an adapter. Most shop vac hoses are 1-7/8 inch or 2-1/2 inch, which do not seal on a 1-1/2 inch port on their own. The GulpDust PETG adapter fits the saw port on one end and your vac hose on the other.
Is the port really 1-1/2 inch?+
The 38.1 mm figure comes from one community adapter listing, and 38.1 mm is the metric size for 1-1/2 inch. It is not a caliper reading on our bench, so measure your own port to be sure before you order.
Do I need clamps to attach the adapter?+
No. The adapter is a friction fit. You press it into the port and it holds. The vac hose end works the same way.
Can I print this adapter myself?+
Yes. You can buy the printed PETG part shipped from the US, or download the STL file and print it at home. We suggest PETG with 3 walls and 25 percent infill.