TP-CS 18/190 Li dust collection adapter and shop vac hose guide
Measure to order
Dust port
Look at the dust port on your Einhell TP-CS 18/190 Li. If it sticks out like a tube, measure the outside. On the TP-CS 18/190 Li, if it is a hole, measure the inside. Use calipers.
More on this port size →Get the adapter for this tool. Printed to order from $12.99, plus $7.95 shipping.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Einhell TP-CS 18/190 Cordless Circular Saw
Specifications
Connect your Einhell TP-CS 18/190 Li to your shop vac
Measure the TP-CS 18/190 Li port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Einhell TP-CS 18/190 is a cordless circular saw. A circular saw throws chips and fine dust hard. Catching it at the port keeps your cut line visible and the bench clear.
The saw has a dust port at the rear. We print the PETG adapter to the size you measure there. One end grips the saw port. The other end takes your shop vac hose.
Einhell TP-CS 18/190 Li Specs
| Port location | Rear |
|---|---|
| Connection type | Press on |
| Blade size | 190 mm |
Einhell TP-CS 18/190 Dust Port: What Connects To It
The dust port on the TP-CS 18/190 sits at the rear of the saw. We print the adapter to the size you measure there.
Most shop vac hoses are 1-7/8 inch or 2-1/2 inch. Neither one seals on this port by itself. That gap is why dust leaks when you tape a hose to a port it does not match.
A GulpDust adapter matches the saw port on one end and your vac hose on the other end for a tight fit.
How to Connect a Shop Vac to the Einhell TP-CS 18/190
Clear any dust out of the rear port first. A clean port gives the best grip.
Push the tool end of the PETG adapter into the port. We print it to the size you measure, so a firm press seats it. Then press your shop vac hose onto the other end.
Turn the vac on before you cut. The vac only pulls dust while it is running.
Why Dust Collection Matters on a Circular Saw
A circular saw sprays chips and fine dust straight out of the guard. Without a hose, that dust lands on your work and hangs in the air.
Pulling the dust at the port keeps your cut line visible so your cuts stay clean. It also keeps more fine dust out of the air you breathe.
For the best result, fit the adapter to the port and run a steady vac while you cut. Any shop vac with the right adapter does the main job.
Einhell TP-CS 18/190 Li Dust Collection FAQ
Will a GulpDust adapter fit the Einhell TP-CS 18/190?+
Yes. The dust port is at the rear, and we print the adapter to the size you measure there. The other end matches your shop vac hose.
Does the Einhell TP-CS 18/190 work with a regular shop vac?+
Yes, with an adapter. Most shop vac hoses are 1-7/8 inch or 2-1/2 inch, so measure the port on your tool and the hose end on your vac. We print the GulpDust PETG adapter to your saw port measurement on one end and to your vac hose size on the other.
Where is the dust port on this Einhell saw?+
It is at the rear of the saw, behind the blade guard, where the chips exit. That is where the adapter goes.
Do I need clamps to attach the adapter?+
Usually not. We print the adapter to the size you measure, so you press it into the port and it holds. The vac hose end works the same way. Add a wrap of tape at any joint that sees heavy use.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
