R48630 dust collection adapter and shop vac hose guide
Measure to order
Dust port
Look at the dust port on your Ridgid R48630. If it sticks out like a tube, measure the outside. On the R48630, if it is a hole, measure the inside. Use calipers.
Get the adapter for this Ridgid R48630.
Tell us the size you measured at the port and the size you measured at the hose, and we print both ends to those two numbers.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Ridgid 18V Brushless 6-1/2 in. Track Saw
Specifications
Connect your Ridgid R48630 to your shop vac
Measure the R48630 port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Ridgid R48630 is an 18V brushless track saw with a 6-1/2 inch blade. It rides on a track to make long, straight cuts in plywood and other sheet goods. Every one of those long cuts pours fine dust right along your cut line.
The dust port on this saw sits at the rear. We print a GulpDust PETG adapter to your port measurement on one end and to your shop vac hose on the other end.
Ridgid R48630 Specs
| Port location | Rear |
|---|---|
| Connection type | Press on |
| Blade size | 6-1/2 in. |
| Power | 18V brushless |
| Tool type | Track saw |
Ridgid R48630 Dust Port: What Connects To It
The R48630 has a dust port at the rear of the saw. Ridgid runs one shared port design across a lot of its cordless line.
We print our PETG adapter to the size you measure at that port. It presses on and holds by friction, so it stays put while the saw runs down the track.
The other end of the adapter takes your shop vac hose. Pick your hose end, 1-1/4 in or 2-1/2 in, and that is the end you get.
Why a Track Saw Needs the Vac at the Port
A track saw cuts long. The blade guard funnels chips straight out the back the whole way down the sheet.
With the vac hooked up, the dust leaves through the hose instead of settling on the track. A clean track means the saw glides and the cut stays straight.
You also see your line. Sheet goods are unforgiving, and a clear line is half the cut.
How to Connect a Shop Vac to the Ridgid R48630 Track Saw
Wipe the port clean first. Packed dust keeps the adapter from seating all the way.
Press the tool end of the PETG adapter onto the port. We print it to the size you measure, so it holds with a firm push. Then press your shop vac hose onto the other end.
Turn the vac on before you cut. A track saw is all about long, clean cuts, and a clear view of the line makes those cuts easier. You also breathe a lot less dust.
Ridgid R48630 Dust Collection FAQ
What fits the dust port on the Ridgid R48630?+
Our PETG adapter does. One end presses onto the saw port. The other end takes your shop vac hose.
Will my shop vac hose fit the Ridgid R48630 without an adapter?+
Some hose ends will seat on their own. A loose hose wobbles and leaks dust down the whole cut. Our adapter locks both ends together.
Does the adapter get in the way of the track?+
No. The port faces back and away from the rail, so the adapter and hose ride clear of the cut.
Can GulpDust make an adapter for this saw?+
Yes. It is printed to order in PETG and ships from the US. Pick your hose size in the configurator.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
