CT1065 dust collection adapter and shop vac hose guide
Measure to order
Dust port
Round port, friction
Look at the dust port on your WEN CT1065. If it sticks out like a tube, measure the outside. On the CT1065, if it is a hole, measure the inside. Use calipers.
Published size
WEN lists the dust port adapter as 35 mm inner diameter, 39.5 mm outer diameter. (WEN manual, checked Oct 10, 2026)
Your port can differ. Measure yours and use that number.
Get the adapter for this WEN CT1065.
Tell us the size you measured at the port and the size you measured at the hose, and we print both ends to those two numbers.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
WEN CT1065 10-Amp 6-1/2 in. Plunge Cut Track Saw
Specifications
Connect your WEN CT1065 to your shop vac
Measure the CT1065 port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The WEN CT1065 is a 10 amp, 6-1/2 in. plunge cut track saw. A track saw earns its keep with long, clean rips, and every one of those rips makes a line of fine dust. Pulling that dust at the port keeps your cut line visible and keeps the track clean, so the next pass glides instead of grinding on grit.
The dust port sits at the back of the saw. We print a GulpDust PETG adapter to your port measurement on one end and to your shop vac hose on the other, so the hose holds instead of falling off mid cut.
WEN CT1065 Specs
| Port shape | Round |
|---|---|
| Port location | Rear |
| Connection type | Press on |
| Blade size | 6-1/2 in. |
WEN CT1065 Dust Port: What Connects To It
The dust port on the CT1065 mounts at the back of the saw. We print the PETG adapter to the size you measure there.
Most shop vac hoses are 1-7/8 in. or 2-1/2 in. Neither one seals on a saw port by itself. That gap is why dust trails behind the saw instead of going into the hose.
The adapter grips the saw port on one end and your vac hose on the other, so you get a snug fit.
How to Connect a Shop Vac to the WEN CT1065
First, clear any packed dust out of the port, so it fits snug.
Press the tool end of the PETG adapter onto the port. We print it to the size you measure, so a firm push holds it. Press your shop vac hose onto the other end. Turn the vac on before you plunge, so the first chips go into the hose and not onto your track.
Why a Track Saw Needs Dust Collection
A track saw cuts fast and makes a lot of fine dust. That dust hangs in the air, and it lands on the track, where it can throw off the next cut.
Pulling the dust right at the port keeps the track clean and the air clear. You see your line, and you breathe easier. On a budget saw like the CT1065, a small printed adapter is all it takes.
WEN CT1065 Dust Collection FAQ
What fits the dust port on the WEN CT1065?+
Our PETG adapter does. One end presses onto the saw port. The other end takes your shop vac hose.
Does the WEN CT1065 work with a regular shop vac?+
Yes, with the right adapter. A shop vac hose and a tool port rarely match, so measure both. We print the GulpDust PETG adapter to your port measurement on one end and to your vac hose on the other.
Does the same adapter fit the WEN 20691 cordless track saw?+
Maybe. Port sizes can change between models. Measure the port on your tool and give us that number.
Do I need clamps or tape to attach the adapter?+
Usually not. We print the adapter to the size you measure, so you push it onto the port and it holds. The same goes for the vac hose end. Add a wrap of tape at any joint that sees heavy use.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
