PTS01 dust collection adapter and shop vac hose guide
Measure to order
Dust port
Look at the dust port on your Ryobi PTS01. If it sticks out like a tube, measure the outside. On the PTS01, if it is a hole, measure the inside. Use calipers.
Get the adapter for this tool. Printed to order from $12.99, plus $7.95 shipping.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Ryobi 18V ONE+ HP 6-1/2 in. Track Saw
Specifications
Connect your Ryobi PTS01 to your shop vac
Measure the PTS01 port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Ryobi PTS01 is an 18V ONE+ HP track saw with a 6-1/2 inch blade. It rides a track for long, straight cuts in plywood and sheet goods. Those cuts pour fine dust right along your line.
The dust port sits at the rear. We print a GulpDust PETG adapter to your port measurement on one end and to your shop vac hose on the other end.
Ryobi PTS01 Specs
| Port location | Rear |
|---|---|
| Connection type | Press on |
| Blade size | 6-1/2 in. |
| Power | 18V ONE+ HP |
Ryobi PTS01 Dust Port: What Connects To It
The PTS01 has a dust port at the rear of the saw. Ryobi runs one shared port design across a lot of its cordless line.
We print our PETG adapter to the size you measure at that port. It presses on and holds by friction, so it stays seated while the saw runs down the track.
The other end takes your shop vac hose. Pick your hose end, 1-1/4 in or 2-1/2 in, and that is the end you get.
Why a Track Saw Needs the Vac at the Port
A track saw cuts long. The blade guard funnels chips out the back for the whole length of the sheet.
With the vac hooked up, that dust leaves through the hose instead of piling on the rail. A clean rail means the saw glides and the cut stays straight.
You also keep your line in sight, which matters most on the cuts you cannot redo.
How to Connect a Shop Vac to the Ryobi PTS01 Track Saw
Wipe the rear port clean first. Packed dust keeps the adapter from seating all the way.
Press the tool end of the PETG adapter onto the port. We print it to the size you measure, so a firm push locks it in. Then press your shop vac hose onto the other end.
Run the vac for the whole cut. A track saw is all about a clean, straight line, and a clear view of that line makes the cut better. Your lungs get a break too.
Ryobi PTS01 Dust Collection FAQ
What fits the dust port on the Ryobi PTS01?+
Our PETG adapter does. One end presses onto the saw port. The other end takes your shop vac hose.
Will a shop vac hose fit the Ryobi PTS01 without an adapter?+
Some hose ends will seat on their own. A loose hose wobbles and leaks dust down the whole cut. Our adapter locks both ends together.
Does the adapter get in the way of the track?+
No. The port faces back and away from the rail, so the adapter and hose ride clear of the cut.
Can GulpDust make an adapter for this saw?+
Yes. Pick the PTS01 in the configurator and choose your hose size. It is printed to order in PETG.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US.
