GTS1041A dust collection adapter and shop vac hose guide
Measure to order
Dust port
Round port, friction
Look at the dust port on your Bosch GTS1041A. If it sticks out like a tube, measure the outside. On the GTS1041A, if it is a hole, measure the inside. Use calipers.
More on this port size →Get the adapter for this Bosch GTS1041A.
Tell us the size you measured at the port and the size you measured at the hose, and we print both ends to those two numbers.
- Made in the USAPrinted to order
- PETGTougher than PLA
- Push onPrinted to your two sizes
- Print defectPhoto within 30 days, reprint or refund
Bosch GTS1041A REAXX 10 in. Table Saw
Specifications
Connect your Bosch GTS1041A to your shop vac
Measure the GTS1041A port and the hose or duct you want on it. We print the adapter between those two numbers. Made in the USA.
Build an adapter for this toolPopular starting points
Full port and fit detail for this tool
The Bosch GTS1041A REAXX is a 10 in. jobsite table saw. A table saw makes more chips than any other tool you own. One long rip cut can dust a whole garage, so sealing the rear port pays off fast.
The saw has a dust port at the rear. A 2-1/2 in. shop vac hose feels close but sits loose on it, so it leaks right where the saw makes the most dust. We print a GulpDust PETG adapter to your port measurement on one end and to your hose on the other end, so the connection holds and the chips go into the vac.
Bosch GTS1041A Specs
| Port shape | Round |
|---|---|
| Port location | Rear |
| Connection type | Press on |
Bosch GTS1041A Dust Port: What Connects To It
We print the adapter to the size you measure there.
A standard 2-1/2 in. shop vac hose slips over this port, wiggles, and blows dust out the gap on every cut. The two parts were never made to seal on each other.
A GulpDust adapter grips this port on one end and your vac hose on the other end, so the suction stays at the blade instead of leaking out the joint.
Port sizes can change between models. Measure the port on the tool you own.
How to Connect a Shop Vac to the Bosch GTS1041A
Unplug the saw first. Then wipe the sawdust off the rear port, so the adapter seats clean and grips all the way around.
Press the saw end of the PETG adapter onto the port. We print it to the size you measure, so a firm push is all it takes. Then press your shop vac hose onto the other end.
Turn the vac on before the blade touches wood. A table saw fires chips down through the blade slot from the first inch of the cut, so the vac needs to be pulling the whole time.
Why the REAXX Deserves Real Dust Collection
You bought this saw because it protects your hands. Your lungs deserve the same care. The fine dust a table saw makes floats in the air long after the cut ends, so you keep breathing it while you sweep.
Pulling dust at the port traps it before it goes airborne, so the air stays clear and the cleanup shrinks to almost nothing.
If you rip a lot of stock, add a cyclone separator between the saw and the vac. The heavy chips drop into a bucket, so your vac filter stays clear and the suction stays strong.
Bosch GTS1041A Dust Collection FAQ
Will a GulpDust adapter fit the Bosch GTS1041A dust port?+
Yes. We print the adapter to the size you measure at the rear port. The other end matches your shop vac hose.
Will a regular shop vac hose fit the GTS1041A port?+
Not by itself. A hose end that does not match the port leaks and can drop off mid cut. The GulpDust PETG adapter grips the port on one end and your hose on the other, so the connection holds tight.
Do I need clamps or tape to attach the adapter?+
Usually not. We print the adapter to the size you measure, so it presses in and holds. You push it on and it holds, so setup takes seconds and comes apart just as fast when you fold the stand. Add a wrap of tape at any joint that sees heavy use.
Does the same adapter fit the Bosch 4100 or GTS1031?+
Maybe. Port sizes can change between models. Measure the port on your tool and give us that number.
Do you sell the design file?+
No. We sell the finished part. Each one is printed to order in PETG and ships from the US. PETG stays stiff and shrugs off shop heat.
Related Guides
Concrete Grinder With Vacuum Setup: Dust Collection and Hose Connections
Surface grinding concrete is dirty work. OSHA Table 1 says you need a HEPA vacuum and a shroud. This guide covers hand-held and floor grinders, rental hookups, and how to measure for the PETG adapter that connects your shroud to your shop vac.
8 min read
Bosch PROFACTOR Dust Collection: How to Measure and Connect Your Tool
Dust port sizes change between Bosch models. Here is how to measure your PROFACTOR or CORE18V tool and your hose, and how to connect them.
4 min read
Angle Grinder Dust Shroud and Vacuum Attachment Guide: Measure and Connect
Shroud port sizes change between models, and shop vac hoses come in different diameters. This guide covers how to pick a shroud, how to measure the port and your hose, and the printed PETG adapter that joins the two.
8 min read
Bosch Power Tool Dust Collection: Measure, Connect, and Capture
Dust ports change between Bosch models. Here is how to measure your tool and your hose, and how to connect to a shop vac, an extractor, or a central collector.
4 min read
